‹ Back to list

CVE-2026-19576

Status: Awaiting AnalysisMedium (6.8)—
Severity6.8Medium · CVSS 3.1
Exploitation probability0.17 %higher than 6% of CVEs
Active exploitationNonot in the CISA catalog
Public exploitNot knownno public code found

The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured.

Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread.

Read full descriptionShow less

Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte.

The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing.

CVSS

Base score
6.8
Version
3.1
Vector
CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

Exploitation probability (EPSS)

Probability of exploitation in the next 30 days
0.17 %
Percentile among all scored CVEs
6
Score date
10/21/2026

EPSS (Exploit Prediction Scoring System, FIRST) estimates how likely a vulnerability is to be exploited in the wild within 30 days. It complements CVSS (impact) and CISA KEV (confirmed exploitation).

ATT&CK techniques

How this vulnerability is exploited and what the attacker gains, in MITRE ATT&CK terms.

AV:P (acceso físico) → T1091. Escritura de stack no acotada con datos controlados por atacante permite ejecución de código en kernel (T1059) y potencial escalada/control de privilegios (T1068).

Inferred by our analysis agent from the official description, CVSS vector and CWE, and checked by a supervisor. May contain errors.

ATT&CK mitigations that cover these techniques

Execution PreventionBehavior Prevention on EndpointDisable or Remove Feature or ProgramThreat Intelligence ProgramRestrict Web-Based ContentPrivileged Account Management

Affected technologies (1)

⚠ AI-inferred from the description — NVD hasn't analyzed this CVE yet, these aren't verified CPEs.

Linux — Linux KernelAI

CWEs

References

Show 2 references

Raw JSON (NVD)

Show
{
  "id": "CVE-2026-19576",
  "cveTags": [],
  "metrics": {
    "ssvcV203": [
      {
        "source": "134c704f-9b21-4f2e-91b3-4a467353bcc0",
        "ssvcData": {
          "id": "CVE-2026-19576",
          "role": "CISA Coordinator",
          "options": [
            {
              "exploitation": "none"
            },
            {
              "automatable": "no"
            },
            {
              "technicalImpact": "total"
            }
          ],
          "version": "2.0.3",
          "timestamp": "2026-10-15T17:57:40.802963Z"
        }
      }
    ],
    "cvssMetricV31": [
      {
        "type": "Secondary",
        "source": "vulnerabilities@zephyrproject.org",
        "cvssData": {
          "scope": "UNCHANGED",
          "version": "3.1",
          "baseScore": 6.8,
          "attackVector": "PHYSICAL",
          "baseSeverity": "MEDIUM",
          "vectorString": "CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H",
          "integrityImpact": "HIGH",
          "userInteraction": "NONE",
          "attackComplexity": "LOW",
          "availabilityImpact": "HIGH",
          "privilegesRequired": "NONE",
          "confidentialityImpact": "HIGH"
        },
        "impactScore": 5.9,
        "exploitabilityScore": 0.9
      }
    ]
  },
  "affected": [
    {
      "source": "vulnerabilities@zephyrproject.org",
      "affectedData": [
        {
          "vendor": "zephyrproject",
          "product": "zephyr",
          "versions": [
            {
              "status": "affected",
              "version": "4.0.0",
              "versionType": "semver",
              "lessThanOrEqual": "4.4.2"
            }
          ],
          "packageName": "zephyr",
          "programFiles": [
            "drivers/input/input_gt911.c"
          ],
          "collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
          "defaultStatus": "unaffected",
          "programRoutines": [
            {
              "name": "gt911_process"
            }
          ]
        }
      ]
    }
  ],
  "published": "2026-10-11T18:16:58.300",
  "references": [
    {
      "url": "https://github.com/zephyrproject-rtos/zephyr/commit/42b52d571eb2113012c135276693042fd372fdea",
      "source": "vulnerabilities@zephyrproject.org"
    },
    {
      "url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-p7qh-fvwx-f7vr",
      "source": "vulnerabilities@zephyrproject.org"
    }
  ],
  "vulnStatus": "Awaiting Analysis",
  "weaknesses": [
    {
      "type": "Secondary",
      "source": "vulnerabilities@zephyrproject.org",
      "description": [
        {
          "lang": "en",
          "value": "CWE-787"
        }
      ]
    }
  ],
  "descriptions": [
    {
      "lang": "en",
      "value": "The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured.\n\nEach loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte.\n\nThe impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing."
    }
  ],
  "lastModified": "2026-10-15T19:17:37.090",
  "sourceIdentifier": "vulnerabilities@zephyrproject.org"
}